The Samsung data migration not working may occur due to various issues, but is very easy to fix and analyse using simple solutions. The article discusses the possible reasons, solutions and an excellent alternative to get your old hard drive data onto a new Samsung SSD.
Samsung offers a data migration tool called Samsing Data Migration to transfer data from one Samsung ssd to another quickly and efficiently. However, some users are encountering Samsung Data Migration stuck at 0 or 99 or not responding errors. This post tries to fix the Samsung Data Migration Not Working issues with efficient solutions.
It is quite difficult to point out what exactly is wrong with the Samsung Data Migration tool, but here are the common issues that could cause the SDM to act up:
We have curated a list of 5 effective solutions and a better substitute to fix the Samsung Data Migration Not Working Issue.
📖Further Reading: Samsung Data Migration Stuck at 0% While Cloning SSD
A bad sector or wrong partition on your source disk or target SSD can strike your Samsung Data Migration at 99 or 0. So the first thing you can try is to run a health check on your device to ensure both are working fine. You can do this with the help of a command prompt, that is run chkdsk on SSD. The instructions are given below:
Step 1: Do not forget to connect the Samsung SSD while running a health check.
Step 2: Open the Command Prompt in Run as Administrator Mode.
Step 3: Run the following command, Press Enter, and follow the prompts on the screen to complete this operation.
chkdsk X: ( Replace the X with the letter of your drive).
If there are any issues with the disk, the operating system will display it on the command prompt.
The Samsung Data Migration Not Working may occur if there are issues with the SATA cable. The process might halt if the SATA to USB connection is not done properly.
First, verify that the SATA/USB is correctly connected, and if the problem persists, try switching the SATA cable to another port on the motherboard or get another SATA port and try to clone important data to the target disk.
Very obviously, if the target disk has less storage space than the source disk, no migration software will be able to transfer the data. If you are trying to transfer data from a 100GB disk to an SSD using Samsung data migration cloning, it will either get stuck in between or shows data migration cloning failed.
Well, to be on the safer side, it is suggested to transfer up to 75% of the total size of the target disk, so prefer buying a suitable disk according to your requirements.
Your computer's hardware condition is vital in managing the software and all functions. So, you need all your hardware to coordinate and carry out the functions. If not, issues such as Data migration failure will pop up.
The PC's hardware is mainly composed of 6 parts: hard disks, CPU, GPU, RAM, and battery. Windows OS has a built-in utility called Performance Monitor to check the overall performance of your computer. The steps to run a Performance Monitor are listed below:
Step 1: Press Windows + R to open the Run dialog box. Type Perform/report and hit Enter to run the utility.
Step 2: The software collects the data for over 60 seconds and displays the Diagnostic results. Now, click on the Diagnostic Results section and know the condition of your hardware components in the subsections.
You can see the Errors, Warning, Informational and Basic System Checks. This is a preliminary check, so try running specific hardware troubleshooters or diagnostic tools to solve the errors.
Sometimes, an outdated Samsung Data Migration tool may cause disk cloning issues. Samsung constantly rolls out updates for the data migration tool. So, to fix the Samsung data migration stuck at 0, visit the official website and update the software.
Step 1: Visit the Samsung Official website.
Step 2: Scroll down and Under Data Migration, Expand Samsung Data Migration software for consumer SSD.
Step 3: Click Download to redownload Samsung Data Migration for Windows with the latest version.
If you still face issues with the Data Migration tool and are tired of fixing it, you could use an alternative to get your job done. Download the EaseUS Disk Copy, set up the requirements, and finish the job with just a few simple clicks.
The EaseUS Disk Copy is a super fast disk cloning software on Windows OS, which offers fast cloning, flexible, and safe boot. The tool benefits you by cloning an old HDD/SSD to a new PC, upgrading your hard drive, migrating operating system to a new hard drive, and recovering data from a failed hard drive. Additionally, you can also avail of backup and restoration services with the help of the same tool. These features are assembled on a simple UI with excellent functionality to carry out in a few steps.
Follow the simple steps to clone to Samsung SSD:
Activate EaseUS Disk Copy for a smooth disk copying or cloning process.
1. Download, install and run EaseUS Disk Copy on your PC.
Click Disk Mode and select the source disk that you want to copy or clone. Click Next to continue.
2. Select the destination disk where you want to clone/copy the old disk and click Next to continue.
Click OK to confirm if the program asks to erase data on the destination disk.
3. Check and edit the disk layout as Autofit the disk, Copy as the source or Edit disk layout.
Autofit the disk is recommended.
Click Proceed to start the disk cloning or disk copying process now.
Well, if you were worried about the Samsung data migration not working issues, you have got your answers to get your data onto the new SSD. The fixes generally try to tackle the potential causes and will solve the issue. If the data migration tool is acting up, you can avail of our simple and compact solution, EaseUS Disk Copy to perform disk cloning for data migration.
If you find this article helpful, share it with your friends and leave a comment about it. If you have any queries regarding the topic, feel free to ask them in the comment box, and do let me know of the future issues you wish to see articles from EaseUS.
Here are some of the most frequent FAQs asked on the topic. If you have similar queries hope this will help you. You can also post your questions in the comment box.
Well, if your Samsung Data Migration cloning failed, you can try the quick fixes below to resolve the issue:
If you connect the SSD with a SATA enclosure, the SDM may not be able to recognize it. There are two things you can do to fix this: try connecting it using a SATA-to-USB cable or Replace the old drive on your computer with a new Samsung SSD and connect the old hard drive with SATA/USB cable.
The reasons are many, but here's what you can do to fix the Samsung Data Migration cloning failure:
The time duration for data migration will depend on the size of the data. The size of the files and the Samsung cloning program largely affect the time, but users have reported that it will take anywhere between 30 minutes to 1 hour.
Related Articles
How to Fix Windows Update Freezes Computer with 7 Solutions
How to Fix Grey Screen of Death Mac, MacBook Air/Pro
Solutions for Disk Not Ejected Properly on Mac
Will System Recovery Delete My Files? Answered Here!